Marine Hardware

Aluminum Base Wire Tie MountThis tie mount is provided with an anodized aluminum base with a nylon tie mount which is riveted to the base. The nylon mount swivels 360 degrees making alignment with the wire harness easier. This tie mount is designed for...

Aluminum Base Wire Tie MountThis tie mount is provided with an anodized aluminum base with a nylon tie mount which is riveted to the base. The nylon mount swivels 360 degrees making alignment with the wire harness easier. This tie mount is designed for...

White Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's...

Black Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's...

AT-5 Large White Nylon Tie Mount - Qty. 500The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength...

Acrylic Adhesive - 10-PackCAN NOT SHIP AIR,UPS GROUND ONLYAT-4020 is a specially formulated adhesive for holding all our parts with little or no sagging in vertical or overhead applications. Cures in 10 - 12 minutes and has working strength within 40 minutes. AT-4020 is...

10:1 Gun Plunger for AT-6030 Adhesive10 Pack Gun Plunger for AT-6030 Adhesive

304 Stainless Standoff 1.25" Base 5/16 x 18 Thread .75" Tall - 6-PackWeld Mount offers wire tie mounts, hose, and cable clamps, studs, standoffs, and floating nutplates. All of the fasteners are mounted with our unique non-sag acrylic adhesives which hold the parts in...

AT-388 Dispensing GunThe AT-388 Adhesive dispensing gun comes with a 10:1 plunger.For Use With 50mL Cartridges of:AT-880Note: The AT-388 will ONLY work with the AT-880 Polypropylene Adhesive Cartridge.  The AT-880 is a 10:1 mix ratio with a teardrop-shaped cartridge, which will not fit in...

White Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50...

White Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50...

AT-3 Small White Nylon Tie Mount - Qty. 500The AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull...

2" Tall Stainless Stud w/3/8" x 16 ThreadThe HS200 stud is designed for heavy load applications such as mounting filters and panels. Thestud is inertial (friction) welded to a 2" base plate creating a very strong part. Manufactured of 304 stainless steel. Tensile strength...

Footman's Strap MountThe Footman's Strap Mount is designed to be bonded with AT-4020 Acrylic Adhesive. This strap mount is 3.25" long and 1" wide and holds up to a 1.3" max strap width. This strap is incredibly strong, paintable, and is rated for over...

10:1 Gun Plunger for AT-6030 AdhesiveSingle Pack gun plunger for AT-6030 Adhesive

Footman's Strap MountThe Footman's Strap Mount is designed to be bonded with AT-4020 Acrylic Adhesive. This strap mount is 3.25" long and 1" wide and holds up to a 1.3" max strap width. This strap is incredibly strong, paintable, and is rated for over...

Adhesively Bonded Fastener Kit with AT 8040 AdhesiveKit Contains: (1) Plano Storage Box - 11" x 7.25" x 2.75" (50) AT-5 Tie Mount (White) (1) AT-8040 Adhesive (5) AT-850 Mixing Tip (1) AT-300 Dispensing Gun (2) AT-113B Black Footmans Loop (4) ST125-1420-16 Stainless Stud...

.75" Tall Stainless Standoff w/5/16" x 8 Threads - Through-ThreadUnlike the SOB standoffs which have a blind thread, the SOT series standoffs have a thread which runs all the way through the barrel of the standoff. This allows the standoff to be mounted from...

2" Tall Stainless Stud w/1/4" x 20 ThreadMounts to virtually any surface using the AT-4010 Acrylic Adhesive. This is a structural part with 500 lbs. of tensile strength and 650 lbs. in shear. All studs have 1/4" x 20 threads. Use for hanging panels,...

1.5" Tall Stainless Stud w/#8 x 32 ThreadOur Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide...